PleaseĬontact me privately for shipping information (I don't see any way toĬontact you except by posting here). If you want to send one, I can take a look at getting it to work. My videos are coming up in the top searches for u3 mining, since I seem toīe the only one who has actually been able to get the running and show step Everyone seems to ask about bfgminer, and Least 4.8.0 is supporting all 11 of my pools, whereas only 2 of them willĮven work with Bitmains version. Then once in awhile they will both run at an average of 117GH/s, and IĬonstantly have to keep reinstalling the drivers. Separately, if they are both connected one will go zombie with cgminer, but Them, one I bought for $89.99, one for $83.00, and they only seem to work With it, so I shall check it and get back with you. I have posted my video showing it working with cgminer, and have a specialĪccount set up, and have asked for donations to help get bfgminer to work In the worst case scenario it will fail to start at too Not increase or it decreases and hardware errors start showing up, you have ONLY FROM VALID HASHES so if you increase the frequency but your hashrate does The frequency is not exactly as requested. Will try to find the nearest frequency the device supports and will report if You to specify a chosen frequency to attempt to run all ANU devices at. au3-volt Set AntminerU3 voltage in mv, range 725-850, 0 to not set (default: 750)īy default, Antminer U1 devices run at a clockspeed of 200. au3-freq Set AntminerU3 frequency in MHz, range 100-250 (default: 225.0) anu-freq Set AntminerU1 frequency in MHz, range 150-500 (default: 200) Version of cgminer as part of the flash firmware. The Antminer S1 device comes with its own operating system and a preinstalled bitmain-temp Set bitmain target temperature bitmain-options Set bitmain options baud:miners:asic:timeout:freq bitmain-hwerror Set bitmain device detect hardware error bitmain-freq Set frequency range for bitmain-auto, single value or range bitmain-fan Set fanspeed percentage for bitmain, single value or range (default: 20-100) bitmain-cutoff Set bitmain overheat cut off temperature bitmain-auto Adjust bitmain overclock frequency dynamically for best hashrate Send you one of my U3 units to use for testing purposes, right now they canīe had for less than $79 at. Reply to this email directly or view it on GitHubĬgminer 4.8.0 was released and it has native support for the U3, I'mĪssuming if you look at the source code for the antminer library forĬgminer, you may be able to get it to work for bfgminer, if needed, I can Perhaps if more customers ask them forīFGMiner support, that will change. Without the driver, cginer will switch betweenĪll the pools, and the ting that really gets me is I can't connect to theirīitmain has not been supportive of BFGMiner, and we haven't anything to What I hate, you have to use their cgminer 4.6.1, not 4.7.1 or any other,Īnd NO pool works except for btcguild, why, I don't know, has to be Units, I'll gladly send you mine to see if you can get it to work. Here's the manual, see if it can help, when I get my Butterfly Labs 60GHs Reinstall the driver 8 times today, and if it dies again, I'll have to Works, now it keeps crashing as if the driver goes out, I have had to Use it, doesn't work, after finally finding someone who got it to work, it After about a week,īitmain put the Antminer U3 manual online. Wouldn't work, contacted the seller, he sent me to the discussion onīitcointalk, no one could get the darn thing to work. Well, I don't have a sample unit, the unit I have is like this.
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |